Steps to connect the Netgear Wi-Fi Range Extend...

Titile

For Netgear Wi-Fi Range Extenders with an available Ethernet port (for example EX6100):-

1. Firstly, Connect your Netgear Wi-Fi Range Extender to your laptop or computer using an Ethernet cable.

2. Now, Open an internet browser and Login to the web interface of your Netgear Wi-Fi Range Extender using the website URL http://www.myWiFiext.net.

3. A login page for Netgear wifi range extender prompts up after visiting the URL of the website named http://www.mywifiext.net prompting you to enter a password and a username.

4. The default Netgear login credentials are given as follows:-

-Username:- admin and Password:- password

5. After logging in successfully, go to Setup option and then click on Wireless Settings.

6. Got to the option of wireless Security and Check the password entered in the Network Key or Password field. It should be the same as your WiFi router password if it is not the same you should change it so it completely matches.

7. Then, click on the Apply button.

8. Reconnect all your Wi-Fi devices to the Netgear Wi-Fi Range Extender.

For Netgear Wi-Fi Range Extender without having an Ethernet port (for example WN1000RP):-

1. Firstly, Reset your Netgear Wi-Fi Range Extender to factory default settings by holding and pressing the reset button on the side panel for approximately about 7 seconds.

2. After that, connect to your NETGEAR Wi-Fi range extender through the Wi-Fi.

3. Open an internet browser and Login to the web interface of your Netgear Wi-Fi Range Extender using the website URL http://www.myWiFiext.net.

4. A login page for Netgear wifi range extender opens up after visiting the website URL http://www.mywifiext.net prompting you to enter a password and a username.

5. The default Netgear wifi range extender login credentials are as follows:

-Username:- admin and Password:- password

6. Run the Smart Netgear router setup wizard for Netgear wifi range extender setup for your connection to your WiFi router.

7. Reconnect all of your wireless devices to the Netgear Wi-Fi Range Extender.

Following are the Steps to cable the Nighthawk Netgear Wi-Fi router:-

1. Firstly, disconnect your modem from the power outlet and leave the modem or WiFi router connected to the wall jack for your Internet service.

2. Remove the battery from your modem or WiFi router in case the modem has a battery backup.

3. Now, connect the modem to a power outlet and turn it on.

4. Replace the batteries in the modem or the WiFi router and connect it to the Internet port of your Netgear WiFi router with the yellow Ethernet cable that came with your WiFi router.

5. Connect the Netgear wireless router to a power outlet through a power adapter.

6. After that, slide the power LED switch on the rear panel to the on position.

7. Then, finally, press the Power button on the rear panel of the WiFi router.

If you face any particular issues regarding the Netgear router setup or the Netgear range extender setup, then you can without any further wait contact our Netgear WiFi router customer support team, where our technical experts are sitting resolve all your issues regarding the Netgear WiFi router or Netgear WiFi range extender. Our expert support team is 24*7 available for your help.

Robert Williams is a self-professed security expert; he has been making the people aware of the security threats. His passion is to write about Cybersecurity, malware, social engineering, Games, internet and new media. He writes for Netgear Router products at netgear router setup .

SOURCEhttp://router-setuphelp.com/2019/03/15/steps-to-connect-the-netgear-wi-fi-range-extender-using-manual-setup/

  0 Votes    0 Comments   Share   Add Bookmark Delete   Delete
DEL2

Comments

Please login or register to comment

Featured